Search Results

High emission performance standards and precious metals costs have pushed the catalytic substrate toward high cell density and thin wall, such as the 600/4, 600/3 and 900/2 products. Due to the inherently lower mechanical strength of these products, coupled with a shift from underbody to close-coupled placement, a concern was expressed that the severe thermal and mechanical conditions may cause structural damage to the substrate, which in turn could impact the catalyst performance. One source of reduced performance during use is the loss of catalyst due to erosion. A previous study1 indicated that the existence of particulate in an air-stream could cause substrate erosion. However, it was not clear if other factors could contribute to or accelerate the erosion process. In order to address this question, experiments were performed to examine the influence of high velocity flow, temperature, impingement angle, particulate characteristics, and coating effect on erosion.

The quality of the environment is a continuing concern of the public in Europe and has been the driving force for much research, development and expenditure by the European Vehicle and Oil Industries. Legislation that has already been implemented and planned provides substantial improvements in air quality. Further improvements however are harder to achieve. Consequently, it has been accepted that a variety of measures, including vehicle/fuel changes need to be investigated together to make further air quality improvements. This paper describes the principles and organisational structure of a co-operative programme carried out by the European automobile industry (represented by ACEA), and the European oil industry (represented by EUROPIA). This programme, building on US AQIRP, is an important input into the process for developing environmental Legislation for the European Union (the European Auto/Oil process).

Engine downsizing is potentially one of the most effective strategies being explored to improve fuel economy. A main problem of downsizing using a turbocharger is the small range of stable functioning of the turbocharger centrifugal compressor at high boost pressures, and hence the measurement of the performance maps of both compressor and turbine. Automotive manufacturers use mainly numerical simulations for internal combustion engines simulations, hence the need of an accurate extrapolation model to get a complete turbine performance map. These complete maps are then used for internal combustion engines calibration. Automotive manufacturers use commercial softwares to extrapolate the turbine narrow performance maps, both mass flow characteristics and the efficiency curve.

An extensive research program involving the French passenger car and heavy-duty (HD) vehicles manufacturers, sponsored by ADEME and realized by IFP, aimed to characterize in terms of size and composition the particulate emitted by the different engine technologies currently or soon available. The impact of engine settings and fuel composition was also studied. Numerous information was collected in this HD study revealing that fuel composition and particularly non-conventional fuels and engine settings strongly impact the particulate concentration and size distribution. Nucleation is likely to occur when there is less adsorption matter, for instance when post-injection is used or EGR is removed. Particulate composition, particularly PAH and sulfates content, is weakly bound to the size. Mineral elements distribution depends on their origin, lubrication oil or engine wear.

Diesel particulate filter (DPF) technology is becoming increasingly established as a practical method for control of particulate emissions from diesel engines. In the year 2000, production vehicles with DPF systems, using metallic fuel additive to assist regeneration, became available in Europe. These early examples of first generation DPF technology are forerunners of more advanced systems likely to be needed by many light-duty vehicles to meet Euro IV emissions legislation scheduled for 2005. Aspects requiring attention in second generation DPF systems are a compromise between regeneration kinetics and ash accumulation. The DPF regeneration event is activated by fuel injection, either late in the combustion cycle (late injection), or after normal combustion (post injection), leading to increased fuel consumption. Therefore for optimum fuel economy, the duration of regeneration and/or the soot ignition temperature must be minimised.

The EPEFE research programme is the largest European investigation of the effects of vehicle/fuel technologies on exhaust emissions. This paper consolidates and summarizes the more than 500 000 data points and compares and contrasts the effects of fuel properties in different vehicles and engines. While the relationships between fuel properties/engine technologies and exhaust emissions are complex, it has been possible to develop equations that model these interactions. The paper demonstrates how the output of EPEFE has been used to predict inventories of emissions from the european traffic for the period 2000-2010. The need for continuing co-operation between the Oil/Auto Industries and the Legislative Authorities to further understand the complex relationships is discussed.

This paper presents a combustion study of gasoline anti-knock quality effects on turbocharged MPI SI engine performances. A comparative analysis between many fuels covering various Research Octane Number (RON), Motor Octane Number (MON) and sensitivity (RON-MON) is described. The study was conducted on steady state test bench, using a four cylinder 2 L engine. In turbocharged gasoline engines, knock resistance is more than ever a crucial issue to achieve high performance and good customer's consumption level. Octane level is therefore a fuel key parameter. Considering thermodynamic aspects of such combustion at full load, performances, fuel consumption and engine thermal strains are evaluated for each tested fuel. An important influence of RON at iso sensitivity was observed. Because of the extreme conditions met on turbocharged gasoline engine, the impact of RON is exacerbated on such engine and illustrates the great benefits of an increase RON fuel.

Laboratory and engine tests were carried out to describe the sulphur effect on the NOx adsorbers catalysts efficiency for gasoline lean burn engines. Two main aspects were studied. The first one deals with the NOx storage efficiency of the adsorber under laboratory conditions, especially regarding the SO2 gas phase concentration. The rate of sulfur storing is greatly affected by the SO2 gas concentration. While 6.5 hours are required to get from 70 % NOx reduction to only 35 % when the gas mixture contains 10 ppm SO2, it takes 20 hours with 5 ppm SO2 and more than 60 hours with the 2 ppm SO2 condition. The relationship between the loss in NOx trap performance and SO2 concentration appears to have an exponential shape. The same amount of sulphur (0.8 % mass) is deposited onto the catalyst within 10 hours with the feed gas containing 10 ppm of SO2 and within 50 hours with 2 ppm SO2. Nevertheless, It was shown that the loss in NOx-Trap efficiency is not the same in these two cases.

This presented paper deals with NOx trap sulphur poisoning and its regeneration. Sulphur poisoning has been studied with different SO2 gas concentrations under laboratory and engine test bench conditions. The sulphur poisoning studies have shown that the different NOx-traps available in the market have different behaviours toward SO2 poisoning and are all very sensitive to it. The results outline a non linear relationship of the NOx trap sulphur poisoning as a function of SO2 concentration. For instance, engine bench tests show that with a 50 and a 110ppm sulphur containing gasoline, a decrease of 50% in the NOx-trap storage capacity is respectively observed after 20 and 15 hours. With a gasoline containing 20ppm of sulphur, the same deactivation level is observed after 90 hours.

NOx adsorbers are very sensitive to sulfur poisoning and future fuel standards are unlikely to be sufficient to prevent the system from requiring periodic desulfation procedures. The purpose of this paper is to present the effects of low fuel sulfur content such as 50 ppm and 10 ppm on the NOx adsorber efficiency for a diesel application. Through this study, the influence of the substrate cell geometry has also been assessed. The use of a 10 ppm sulfur fuel is not enough to maintain, at a high level, the NOx adsorber performance during a 40,000 km aging test. The desulfation criterion (efficiency loss of 30%) is reached after the first 16,000 km. However, the desulfation operation is not enough to recover the initial catalyst performance and the poisoning velocity increases as the catalyst ages. The hexagonal cell substrate catalyst is less sensitive to sulfur poisoning than a square cell substrate catalyst so that its desulfation frequency is much lower.

This paper proposes a method to detect an intake manifold leakage for a Diesel engine with a dual loop EGR system. The intake manifold leak has a strong impact on the engine performances by changing the intake manifold burned gas ratio. This fault is analyzed according to the control structure used and also according to the EGR operating mode. The paper proposes a diagnosis algorithm to detect the intake manifold leak in sequential or simultaneous use of the two EGR paths. The sensors considered are the mass air flow meter, the intake manifold pressure sensor, the exhaust equivalence ratio sensor and the differential pressure sensor (across the HP EGR valve). The diagnosis is based on a criteria that uses the redundancy between these sensors and air system models or estimators. The diagnosis threshold depends on the engine operating conditions as well as the sensor or model dispersions.

Impact noise, inside a car, due to tire-launched gravel on the road can lead to loss of quality perception. Gravel noise is mainly caused by small-sized particles which are too small to be seen on the road by the driver. The investigation focuses on the identification of the mechanisms of excitation and transfer. The spatial distribution of the particles flying from a tire is determined, as well as the probable impact locations on the vehicle body-panels. Finally the relative noise contributions of the body-panels are estimated by adding the panel-to-ear transfer functions. This form of Transfer-Path-Analysis allows vehicle optimization and target setting on the level of the tires, exterior panel treatment and isolation.

Partially Premixed Combustion (PPC) of fuels in the gasoline octane range has proven its potential to achieve simultaneous reduction in soot and NOX emissions, combined with high indicated efficiencies; while still retaining proper control over combustion phasing with the injection event, contrary to fully premixed strategies. However, gasoline fuels with high octane number as the commonly available for the public provide a challenge to ensure reliable ignition especially in the low load range, while fuel blends with lower octane numbers present problems for extending the ignition delay in the high load range and avoid the onset of knocking-like combustion. Thus, choosing an appropriate fuel and injection strategy is critical to solve these issues, assuring successful PPC operation in the full engine map.

A new simulation approach to the modeling of the whole fuel injection process within a common-rail fuel injection system for direct-injection gasoline engines, including the pressure-swirl atomizer and the conical hollow-cone spray formed at the nozzle exit, is presented. The flow development in the common-rail fuel injection system is simulated using an 1-D model which accounts for the wave dynamics within the system and predicts the actual injection pressure and injection rate throughout the nozzle. The details of the flow inside its various flow passages and the discharge hole of the pressure-swirl atomizer are investigated using a two-phase CFD model which calculates the location of the liquid-gas interface using the VOF method and estimates the transient formation of the liquid film developing on the walls of the discharge hole due to the centrifugal forces acting on the swirling fluid.

Laboratory and vehicle tests were carried out to investigate behaviour and potentiality of NOx-trap catalytic system in Diesel conditions. Three main aspects were studied. The first one deals with the NOx storage capacity of adsorber under laboratory and vehicle conditions, especially regarding the influence of driving conditions. The second one focuses on the regenerability of different materials. At length, special attention is devoted to the sulphur poisoning rate. A representative laboratory test method was built up, to evaluate NOx storage capacity under Diesel conditions. It is shown that NOx adsorption occurs from 100 to 400°C. Low temperature activity (100 to 250°C) is conditioned by low NOx flow emission, mainly due to the use of high EGR rate. Higher temperatures lead to an increase in the intrinsic NOx Storage capacity of the material, but are also accompanied by high NOx concentration and space velocity.

No efficient catalyst presently exists for deNOx in lean burn conditions. Furthermore, actual catalysts generally deactivate during reaction. A cylindrical DBD non-thermal plasma reactor was coupled with a stable three-function catalyst in order to verify the nature of the effect of the plasma on the catalytic process. A mixture of NO/O2/C3H6 in N2 was used as a lean model exhaust. The plasma was found to perform two of the three functions: NO oxidation to NO2 and propene activation through the partial oxidation of the hydrocarbon to aldehyde or alcohol. A complete catalyst containing the first two previous functions and the associative chemisorption of NO (third function) was used, as well as a simplified catalyst containing only the third function. Results suggest an advantageous plasma-catalyst coupling effect on NOx remediation in accordance with the proposed catalytic model.

This paper touches on the mass transport phenomenon in the exhaust gas recirculation (EGR) of a gasoline engine air path. It presents the control-oriented model and control design of the burned gas ratio (BGR) transport phenomenon, witnessed in the intake path of an internal combustion engine (ICE), due to the redirection of burned gases to the intake path by the low-pressure EGR (LP-EGR). Based on a nonlinear AMESim® model of the engine, the BGR in the intake manifold is modeled as a state-space (SS) output time-delay model, or alternatively as an ODE-PDE coupled system, that take into account the time delay between the moment at which the combusted gases leave the exhaust manifold and that at which they are readmitted in the intake manifold. In addition to their mass transport delay, the BGRs in the intake path are also subject to state and input inequality constraints.

The target of substantial CO₂ reductions in the spirit of the Kyoto Protocol as well as higher engine efficiency requirements has increased research efforts into hybridization of passenger cars. In the frame of this hybridization, there is a real need to develop small Internal Combustion Engines (ICE) with high power density. The two-stroke cycle can be a solution to reach these goals, allowing reductions of engine displacement, size and weight while maintaining good NVH, power and consumption levels. Reducing the number of cylinders, could also help reduce engine cost. Taking advantage of a strong interaction between the design office, 0D system simulations and 3D CFD computations, a specific methodology was set up in order to define a first optimized version of a two-stroke uniflow diesel engine. The main geometrical specifications (displacement, architecture) were chosen at the beginning of the study based on a bibliographic pre-study and the power target in terms.

The purpose of the European « SPACE LIGHT » (Whole SPACE combustion for LIGHT duty diesel vehicles) 3-year project launched in 2001 is to research and develop an innovative Homogeneous internal mixture Charged Compression Ignition (HCCI) for passenger cars diesel engine where the combustion process can take place simultaneously in the whole SPACE of the combustion chamber while providing almost no NOx and particulates emissions. This paper presents the whole project with the main R&D tasks necessary to comply with the industrial and technical objectives of the project. The research approach adopted is briefly described. It is then followed by a detailed description of the most recent progress achieved during the tasks recently undertaken. The methodology adopted starts from the research study of the in-cylinder combustion specifications necessary to achieve HCCI combustion from experimental single cylinder engines testing in premixed charged conditions.

Four Diesel vehicles and two gasoline ones are used to determine the repeatability of the particle number and size measurements. Two analytical techniques are used: Scanning Mobility Particle Sizer (SMPS) and Electrical Low Pressure Impactor (ELPI). The influence of technology (Euro2 and Euro3, Diesel and gasoline vehicles, Diesel Particulate Filter (DPF), Gasoline Direct Injection (GDI)) and speed on the particle number and size is presented in the case of steady speeds and the European Driving Cycle (EDC). The repeatability of these measurements is determined at the entire particle distribution. The global 1.96*Standard Deviation (SD) of the median diameter, determined by SMPS, is 8 nm. The median diameter is difficult to be determined in several cases due to the flat profiles of the emitted particles. The global 1.96*Relative Standard Deviation (RSD) of the particle number presents a U-like curve, with a minimum value (55-57%) at about 100 nm.